Double the Invisible Wireless Charging
Powered by patented Intelligent Power Communication™ Technology (IPC)
Apple & Samsung Fast Charge
Easy on your Battery Health
Safe, reliable, Rugged
Precision distance switch
Daisy chain Option
no damage installation
one year warranty
Audio Calibration Assitance
auto-shut off when fully charged
DOES NOT WORK THROUGH
expand your charging network
The world's first non-invasive daisy chained enabled wireless charger
Whereever you have one UTS-1 you can have two using the unique daisy chain capability.* Create small charging stations to share with your family or colleagues to ensure nobody forgets to give back your charger!
*Connecting two UTS-1 can only be done with the daisy chain power adaptor which is included in the daisy chain set but sold separately from single unit pack.
Keep the whole family charged throughout the day and clean up those wires.
OPEN PLAN OFFICES
Perfect for long chains of desks to keep to stop the overspill of wires at workstations.
Impress your visitors and clients with an extra wireless charging service during meetings to leave them informed and charged.
The UTS-1 is compatible with iPhone 12 and MagSafe designs up to 20mm (0.8"). iPhone 12 Pro Max compatibility and performance may be reduced due to additional camera module thickness.
The presence of magnets in the iPhone 12 series creates more interference with our charging signal meaning the overall charging distance needs to be reduced to 10-20mm (0.39" - 0.80") to improve compatibility.
iPhone 12 charge times can vary significantly depending on camera module dimensions, placement accuracy and additional MagSafe Case usage. All iPhone 12 models enter a slower charging mode once the battery level exceeds 80% due to battery and software limitations set by Apple. A combination of these conditions may result in devices not being fully charged to 100% after a full overnight charge.
For best charging results please charge without a MagSafe case as this further increases magnetic interference and charging distance.
Support.Apple.com states the following:
- When charging a non-MagSafe Qi-compatible device with a MagSafe Charger, power is reduced and charge times may be slower than on a typical Qi charger.
- If your iPhone is connected to both a MagSafe Charger and power via a Lightning port, your iPhone will charge via the Lightning connector.
- As with other wireless chargers, your iPhone or MagSafe Charger might get slightly warmer while your iPhone charges. To extend the lifespan of your battery, if the battery gets too warm, software might limit charging above 80 percent.
- Please ensure the power adapter is plugged in all the way.
- If No 1. does achieve a solid light - please unplug and re-plug in the power cable to the unit.
- Please plug in the charger to a single point power (not a multi-plug extension cable) if it is not already so and check again.
- A flashing LED is therefore an electrical system fault error( please see LED indication section (Page 12) on the user instructions.
- If you have a phone case, it is flat and does not contain any metal, centrally located magnets, card holders, pop sockets or kickstands.
- Ensure your phone is aligned as centrally as possible.
- Check if your phone is Qi wirelessly charging enabled.
- Check your sticker position through recalibration.
- Check your table thickness is within the stated performance range.
25mm (1.0”). Thicker cases can also cause longer recognition time and therefore longer time to beep. Recalibrate if necessary to improve sticker position or center your device on the sticker more accurately to get a better alignment.
Yes – if you would prefer or need to use the charger without the audio confirmation buzzer system, you are able to turn it off. However, without the audio confirmation, your phone is not necessarily charging just through the charging indication on your screen. If you choose to use the device without the buzzer, please ensure your alignment and setup is correct and accurate.
- To disable the buzzer.
- Switch your height toggle switch to calibration mode and switch back to your original height position and listen for the number of audio beeps
- Repeat again to disable or enable depending on preference.
Different phone models have different battery sizes and charging profiles therefore take different amounts of time to charge, with large batteries especially taking longer. Charging speeds may also slow at ≥80% in IOS models due to Apple software requirements designed to limit battery deterioration during wireless charging.
The UTS-1 recognises IOS charging signals and corresponds by adapting charging speeds until your device requests more power. Please try turning OFF ‘Optimised Battery Charging’ in your ‘Settings’.
Charging speeds will also vary depending on the surface thickness. Thicker surfaces will reduce charging efficiency due to the greater distance the charging signal needs to travel.
If problems persist - please reach out to [email protected] for further help.
INCLUDED IN THE BOX
User manual, wire clips, installation templates, x2 UTS-1, 60w power adaptor, stickers, screws, double sided tape (pre-positioned)
12V 5A DC adaptor for daisy chain connection - must be be used with 2 units connected at all times.
Intelligent Power Communication™ (IPC)
Apple Samsung Fast Charge
Qi Wireless Charging
Product dimensions and weight
Each unit - 18.2 x 12.2 x 2cm (7.17" x 4.8" x 0.79")
30W output power each UTS-1
Apple 7.5W Fast Charge
Samsung 9W Fast Charge,
Qi standard 5W normal charger
UL, CE, FCC, KR, JP
I ordered the charger being sceptical, as it is to use with the quartz countertop .... and it works!
Tried through 20 mm surface and my Samsung S10e charges with no problems.
NOTE - I didn't check whether it is a fast charge or not, as it is not of great importance. The charger is not yet fitted, and I just tried it through my existing counter top.
I need to add that shipping (even to Europe) is incredibly fast and pre-sale and after-sale support deserves 5 stars.
Thank you guys
I can't recommend this company or their product (UTS-1) highly enough!
Firstly, delivery. 48 hours door to door (USA to UK!) courtesy of FedEx. I was quite impressed with that.
And then there's the product itself. The set up instructions couldn't be clearer or more straight forward to complete. The quality of the build for this device is first rate and it just works. It does exactly what it promises to. So now my desk looks like a desk... no unsightly/bulky chargers and associated cables... just a desk with a phone on, that happens to be quietly charging. I love it!
Although I had to do a little experimenting with material thickness plus my Otter Defender case the Kew lab does the job.
I tried different thickness material from magazines to 1/4" wood with my phone case on before it was consistent in locating the
sweet spot. I suppose if the phone didn't have a case it would have been closer to what I initially thought it would be like.
Unfortunately, taking the case off just to charge would be a real pain.
It seems like long distance charging is difficult and Kew Labs seems to be one of the better options out there. It may work for you if you have a slightly thinner less dense surface, but unfortunately, it did not work for me. Wireless charging is spotty and inconsistent and wireless fast charging is worse. Even with the cases removed, our Samsung S10 and S10e rarely can fast charge, let alone get normal charge since you have to put the phone in the EXACT center of the charger with little room for error (extra hard at night). Also (and this could be a problem with all wireless charging) leaving the phone over night to charge, it would be scalding hot, and rarely at 100% in the morning. I suspect it would work better on a thinner surface as my solid oak nightstand is right at the upper advertised limit of 1 inch, but I have not tried that.
However, their customer support team were very helpful in trying to help trouble shoot, and ultimately process the refund that they deserve credit for making things right.
I've try many wireless charger for under desk mount and nothing came close the UTS-1. Highly recommended.